Previous Thread
Next Thread
New Reply
Print Thread
Rate Thread

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
The Complete Paint Guide with Pictures

In this guide, I will walk through the steps to creating a professional paint job on virtually any piece of your car that you desire. I will be using the center console of my 2001 Celica GT.

The first, and most important step with any paint job is to prepare the surface that you are painting. Paint will adhere best to a clean, oil-free, dull surface. Begin by making sure that your part is is clean; use a mild detergent in warm water to break up and carry away any dirt on the surface.

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Next, dull the surface with 400 grit sandpaper. This will remove any minor surface imperfections, and the added surface area in the 400 grit scratches will give the paint more surface to adhere to. After the 400 grit, step up to 800 grit, and sand the surface until it looks even, and is smooth to the touch.

Once you are done with the sanding, wash the piece again with warm soapy water. The final step in cleaning and prepping the surface is to wipe it down with mineral spirits (paint thinner). This should be done once or twice, and allowed to dry completely before any paint is sprayed onto the surface.
1869791556-Mvc-026s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
paint thinner...
1869791563-Mvc-020s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Next, we move on to the primer coat. It is essential to get a good even primer coat on the piece, as any imperfection in the primer will rear its ugly head in the finished paint.

Begin, and do this as a general rule before you spray ANY kind of paint, by wiping down the surface gently with tack cloth (roughly $.45 at a paint store or walmart). This will remove any dust, dirt, lint, etc. from the surface. Do this immediately before you paint, and this will lesson the chance of anything getting caught in the paint.

You will get the best finish with a high build primer/surfacer. This should be sprayed on in several thin coats, tack clothing in between each. Make sure that you get good coverage, but be careful not to lay it on so thick that it runs or sags.

Once you get done spraying your coats of primer, and it has dried for at least 6 hours, you should lightly sand the surface with 1000 grit sandpaper. Continue sanding lightly, in a circular pattern, until the surface appears even and is completely smooth to the touch. If you should happen to sand through the primer, fear not, just tack cloth the piece again, and spray a few more light coats onto it. It's important to remember that you don't have to sand the piece too hard, the paint will sand easily, with little pressure, so be gentle.

Wash the piece again with soap and water.


1869791565-Mvc-021s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
sandpaper...
1869791571-Mvc-025s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Now, on to the good stuff... the color coat.

For this, you should use a paint that is formulated for your specific application. Example, if you're painting a valve cover, use high heat engine paint; if it's a urethane bumper, use a flexible exterior paint, etc.

Again, make sure that you have cleaned the surface to get any oils off of it, and that the surface is completely dry. You should give the primer coat at least overnight to dry completely. Tack cloth the piece before spraying.

The color should be laid on in several thin coats. Don't worry about covering the the primer in the first couple of coats, just go lightly. In fact, four coats is usually a good beginning for the color. After the primer is completely covered, and the paint has dried for at least six hours, take the piece to the bathtub or sink, and hold the piece under luke-warm water, and sand it very lightly with 2000 grit sandpaper. Let the piece dry, and inspect it to see that the primer isn't showing through anywhere, and that the sanding has created an even, smooth surface. If there are any deep scratches, or any dust blebs, sand them out now. The finished appearance of the sanded paint will be dull and cloudy. Don't worry, that will change when you clear coat it.

Once you have the color coat evenly sanded, and the primer completely covered, let the paint dry over night.

1869791573-Mvc-016s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Alright, we're getting close, don't quit now!

After the color has had a night to dry completely, you can clear coat the paint to really bring out the color, and add depth to the paint.

I usually like to use at least three seperate coats of clear-coat.

Each of these coats whould be applied exactly liek the color coat, in several thin layers. The sanding is where it differs, however. Instead of using sandpaper, invest in some 0000 grade steel wool (around $4.00 at a paint store, or walmart). This should be used very lightly after the first two clear coats, without any water. Again, strive to make the surface smooth and even. Every time you sand it, it will get cloudy, and the next layer of clear coat will make it clear again. Make sure that you rinse the piece after every time that you sand it, and the let towel it completely dry. Tack cloth it immediately before every layer of clear coat to remove any leftover steel wool fibers, or lint.

After the final clear coat, VERY gently wet sand the paint with 0000 grade steel wool. Yes, i know, this will make the paint cloudy again. Don't worry, it's not going to stay that way.
1869791576-Mvc-024s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
The final step is to give the paint its gloss by buffing out the fine scratches.

The best product for this is 3M brand Rubbing Compound (part #03900). This will remove 1500 grit and finer scratches. Use a clean terry cloth rag to apply a small amount to the surface of the paint, and rub using a smooth circular motion. When the compound starts to dry, lighten your pressure. Turn to a clean portion of the cloth and gently buff the dried compund off the paint. Repeat this until the paint has a mirror gloss. You can bring the paint to an even higher gloss by using Meguiar's Deep Crystal polish. It is best, after you have used a paint polish, to let the paint cure for about a month (depending on the humidity of your area), then you can use your favorite car wax to maintain the finish of the paint. You should not wax the paint before the month is over, as it will seal the paint, and prevent it from curing and completely adhering to the piece that you painted.
1869791584-Mvc-022s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
polish and wax...
1869791587-Mvc-023s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Thanks everyone! I hope this helps some of you out with your custom work. Enjoy!

If you have any other questions, or comments, you can PM me, or send me an email to: RaderStudios@hotmail.com



[Linked Image]

Joined: Apr 2003
Posts: 1,917
Blue MnM
2003 Toyota Celica
Blue MnM
2003 Toyota Celica
Joined: Apr 2003
Posts: 1,917
this is a great guide but can you post pics of the actual final product of your center console painted i wanna see the difference between doing all the steps you listed and just painting it without sanding thumbsup

Joined: Nov 2003
Posts: 660
Senior Member
1995 Toyota Celica ST
Senior Member
1995 Toyota Celica ST
Joined: Nov 2003
Posts: 660
you prob won't be able to tell much of a difference in a picture, his way will look much better up close, have more detail, and most importantly last a lot longer.

painting without preping will never last as long and will get chips very easily like if you bump into it with something hard or bend it to much when puting it back on.

this guid is one of the most comprhensive i've ever seen, MAD MAD PROPS!!! thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup thumbsup keep up the good work.

it would be nice to have pics of an actual peice going through the process.

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
I agree, but the problem is (and i feel bad about this) I haven't had time to actually finish my center console yet. I just went ahead and did the paint guide because people seemed like they wanted to have the info. Fear not, when I actually get time to do it, i will post some pics of the process, or at least the finished product.

Last edited by isaac; Jul 24, 2004 8:10pm.

[Linked Image]

Joined: Jun 2003
Posts: 1,305
Specialist
2002 Toyota Celica GT
Specialist
2002 Toyota Celica GT
Joined: Jun 2003
Posts: 1,305
Hey Jon were did you get a 1000grit sand paper???
When i was painting my centr console i used 600grit . I went to couple of stores but no one sells higher than 600 wtf
P.S.Very good installation gude.

Last edited by RoMkApOmKa; Jan 25, 2004 12:55am.

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
You should be able to pick up 1000, 1500, and 2000 grit at your local autozone, pepboys, checker/schucks/kragen, or any auto body supply shops


[Linked Image]

Joined: Jul 2003
Posts: 500
Bruce Leroy
2002 Toyota Celica GTS
Bruce Leroy
2002 Toyota Celica GTS
Joined: Jul 2003
Posts: 500
I just wanted to thank Carbon again for this guide.
I've started painting my enging plastics again. I'm just painting the small plastic piece on the drivers side for now. I just put the first clear coat on this morning and all I can say is WOW eek It looks like a professional did. As soon as it's finished I'll post pic's so everyone can see the difference.
Thanks again. thumbsup

Last edited by GTSHYPR; Feb 4, 2004 11:21am.

I'm gonna take your little Civic. Dust it off. Turn it sideways and stick it straight up you candy A*s.

Joined: Jul 2003
Posts: 500
Bruce Leroy
2002 Toyota Celica GTS
Bruce Leroy
2002 Toyota Celica GTS
Joined: Jul 2003
Posts: 500
Sorry I didn't post this yesterday my computer was down.
1869813829-Paint Shop.jpg


I'm gonna take your little Civic. Dust it off. Turn it sideways and stick it straight up you candy A*s.

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
WOW, the little piece looks awesome!! Good work!


[Linked Image]

Joined: Jul 2003
Posts: 500
Bruce Leroy
2002 Toyota Celica GTS
Bruce Leroy
2002 Toyota Celica GTS
Joined: Jul 2003
Posts: 500
I'm thinking about makeing it a little darker. Is there anything special that I need to do or can I just sand off the clear coat?


I'm gonna take your little Civic. Dust it off. Turn it sideways and stick it straight up you candy A*s.

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Um.. pretty much the only thing you can do is to repaint it with a darker blue. So, you should scuff up the paint that's on it now with some 0000 grade steel wool, and then you can just spray your darker blue coat over that, no need to re-prime it, the paint will bond to the ruffed-up clear coat nicely.


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
here's a shot of the beginning of my project painting Claypeanutz center console...
1869815308-Mvc-012s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
and here i just got done sanding a piece of my center console after my first coat of black...
1869815310-Mvc-011s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
here's the top piece of my center console after the last coat of black, and before i sand it in preparation for the clear coat...
1869815312-Mvc-010s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
and here's the middle piece of my center console, finished, completely, as done as it's getting. The bottom piece of my console already looks like this, and it's already installed in my car.
1869815313-Mvc-002s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
oh yeah, and here's a shot of my shop... messy huh?
1869815322-Mvc-008s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
My finished console...
1869818080-Mvc-001s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
another...
1869818085-Mvc-004s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
again...
1869818087-Mvc-005s.jpg


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
last one
1869818090-Mvc-003s.jpg


[Linked Image]

Joined: Jul 2003
Posts: 500
Bruce Leroy
2002 Toyota Celica GTS
Bruce Leroy
2002 Toyota Celica GTS
Joined: Jul 2003
Posts: 500
Originally Posted by carbon_blue_gt
Originally Posted by GTSHYPR
I'm thinking about makeing it a little darker. Is there anything special that I need to do or can I just sand off the clear coat?

Um.. pretty much the only thing you can do is to repaint it with a darker blue. So, you should scuff up the paint that's on it now with some 0000 grade steel wool, and then you can just spray your darker blue coat over that, no need to re-prime it, the paint will bond to the ruffed-up clear coat nicely.

Thanks I just used the same color and put more coats on. It is almost the exact color of my car. I just need to put the clear coats on and I'm done I'll post pic's maybe tomorrow morning. thumbsup


I'm gonna take your little Civic. Dust it off. Turn it sideways and stick it straight up you candy A*s.

Joined: Jan 2004
Posts: 2
New Member
2002 Toyota Celica GT
New Member
2002 Toyota Celica GT
Joined: Jan 2004
Posts: 2
the only thing i did different was i taped off the areas around the ac lights because you still have that color trim in the car and the lights look a little tacky shining through the paint and this way you can still see your ac setting in the day time

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
If you use good paint, and the proper number of coats of paint, there is no way the lights are gonna shine through. Also, if you're still worried about, you can always take the bulbs out before you replace the console. There's a guy on one of the other forums that sells vinyl sticker kits that replace the stock control designations, and I am going to look into developing some in photoshop that can them be printed on vinyl.

That way, you can completely get rid of the hideous gray color, and still have your controls visible.


[Linked Image]

Joined: Jul 2003
Posts: 500
Bruce Leroy
2002 Toyota Celica GTS
Bruce Leroy
2002 Toyota Celica GTS
Joined: Jul 2003
Posts: 500
I've been waitting for someone to make vinyl's for the controls. So you have a link for that? Thanks

Oh and the Pic's that I posted w/ the dark blue paint that was without the clear coat. It's a lot more shinny now.


I'm gonna take your little Civic. Dust it off. Turn it sideways and stick it straight up you candy A*s.

Joined: Sep 2003
Posts: 3,977
Furi Kuri
2002 Toyota Celica GT
Furi Kuri
2002 Toyota Celica GT
Joined: Sep 2003
Posts: 3,977
how much was the supplies in total? Is Dupli-Color a good brand of paint?

Nice job with the painting. I will re-do my plastics using this guide! I love the way your plastics shine! thumbsup


I've mastered the art of the After Image Technique.

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Bear in mind that I buy bulk products, somy cost is a lot higher than yours, but my cost for my project was around $50 for paint sandpaper and steel wool.

Duplicolor is actually a very good brand. It's ownedandmanufactured by Sherwin-Williams in Cleveland. Good luck, have fun,and post pics when you're done!


[Linked Image]

Joined: Feb 2004
Posts: 1
New Member
New Member
Joined: Feb 2004
Posts: 1
anyone know how to powder coat body kits and other larger acessories?

Joined: Jan 2004
Posts: 2
New Member
2002 Toyota Celica GT
New Member
2002 Toyota Celica GT
Joined: Jan 2004
Posts: 2
Originally Posted by CheesyP18
anyone know how to powder coat body kits and other larger acessories?

yes but powder coating is for metal you need to buy a powder coater witch is just like a spray gun only it shoots out metal flakes then you put in in a powdercoating oven witch isnt anything different that your oven at home only you can get it bigger and its preset to the right temp, but anyway you leave it in the oven for 20-30 min on like 375 until the flakes melt and you let it sit for and hour or two. its pritty much anadizing but you can do it on any metal and you have more colors to choose from.

ps a powdercoater is kinda pricey and you need a compressor and the use of an oven and if your not exactly even with your coats its a little harder to sand smooth, so id say practice a few times before you try it on somthing you really wanna do

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Originally Posted by seanslica
Originally Posted by CheesyP18
anyone know how to powder coat body kits and other larger acessories?

yes but powder coating is for metal you need to buy a powder coater witch is just like a spray gun only it shoots out metal flakes then you put in in a powdercoating oven witch isnt anything different that your oven at home only you can get it bigger and its preset to the right temp, but anyway you leave it in the oven for 20-30 min on like 375 until the flakes melt and you let it sit for and hour or two. its pritty much anadizing but you can do it on any metal and you have more colors to choose from.

ps a powdercoater is kinda pricey and you need a compressor and the use of an oven and if your not exactly even with your coats its a little harder to sand smooth, so id say practice a few times before you try it on somthing you really wanna do

All you need is a good HVLP spray gun, a compressor that runs at a minimum of 7-9 Carbon FiberM, and a big, dust free building to spray it in. Then, you need an oven big enough to put the part that you're powdercoating in. As far as i know, powdercoating won't stick any better than regular paint on Fiberglass, and Urethane would warp at the temps that powdercoating cures at. So, powdercoating a body kit is virtually pointless. Paint it. Intakes, wheels, brake calipers, control arms, valve covers, alternators, superchargers and Turbos tasty These are the kind of things that you would want to powdercoat.


[Linked Image]

Joined: Feb 2004
Posts: 14
Member
2000 Toyota Celica GTS
Member
2000 Toyota Celica GTS
Joined: Feb 2004
Posts: 14
nice what kind of black is the painted console?

Joined: May 2002
Posts: 5,979
Likes: 9
ECelica Admin
2001 Toyota Celica GT
ECelica Admin
2001 Toyota Celica GT
Joined: May 2002
Posts: 5,979
Likes: 9

Last edited by isaac; May 2, 2004 8:13pm.

[Linked Image]
It's not just your imagination...
Your day really does go by twice as fast while on EverythingCelica.com

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
Originally Posted by tedd69
nice what kind of black is the painted console?

It's Duplicolor t-100 universal black.


[Linked Image]

Joined: Feb 2005
Posts: 4
New Member
1991 Toyota Celica GTI
New Member
1991 Toyota Celica GTI
Joined: Feb 2005
Posts: 4
First of all, great guide! thumbsup

Got a question for you.
If I want to use this technique but doesn't want the glossy finish, can I just exchange the clear coat with some dull coat(not sure about the right word here).

Or is there something else I should do?

Joined: Sep 2003
Posts: 3,977
Furi Kuri
2002 Toyota Celica GT
Furi Kuri
2002 Toyota Celica GT
Joined: Sep 2003
Posts: 3,977
^^^just dont use a clear coat. or if you dont want a glossy shine to it, use flat colors. thumbsup


I've mastered the art of the After Image Technique.

Joined: Feb 2005
Posts: 4
New Member
1991 Toyota Celica GTI
New Member
1991 Toyota Celica GTI
Joined: Feb 2005
Posts: 4
Originally Posted by Zero
^^^just dont use a clear coat. or if you dont want a glossy shine to it, use flat colors. thumbsup
Well, I want to protect the paint with some kind of coat.
And even if I use flat colors, the clear coat will make it too shiny.

Join the conversation - Register Now or Log In to add your comment


Link Copied to Clipboard
Member Spotlight
BLACKGHOST
BLACKGHOST
2003 Toyota Celica GT
IL

Posts: 35
Joined: January 2004
Thank you.: Mama thomas, michelle, mike, scooby,leeo,heavensknight crew westbury,ny
Random: Night time is my time come out and play see ya in the streets.
Show All Member Profiles 
Recent Topics
Spyder Headlight LEDs
by Dxnxld - Mar 25, 2024 6:51am
Anyone ever hear this noise?
by CeliacCelica - Mar 21, 2024 10:51am
Clunking sound (not sure where from)
by Juliansky - Mar 20, 2024 3:01am
Does anybody know where i can find a S53 trans rebuild kit?
by MoreRamenNoodles - Mar 19, 2024 8:57pm
Urgent
by SoloXKay - Mar 19, 2024 11:58am
OEM speedometer on aftermarket ecu
by Penaman99 - Mar 5, 2024 11:23am
Brake master cylinder
by Nigel100 - Mar 5, 2024 2:45am
newly purchased 2000 GTS
by CantShift - Feb 27, 2024 9:06pm
Customize Your Toyota Celica Privacy Policy · About · Contact
Privacy Policy · About · Contact
CelicaHobby.com is an independent Toyota Celica enthusiast website. CelicaHobby.com is not sponsored by or affiliated with Toyota Motor Sales, USA, Inc. in any way. The Toyota and Celica names and logos are trademarks owned by Toyota Motor Sales, USA, Inc.
© CelicaHobby.com, 2001-2024
Powered by UBB.threads™ PHP Forum Software 8.0.0
(Preview build 20230331)