Previous Thread
Next Thread
New Reply
Print Thread
Joined: Aug 2004
Posts: 993
Celica2k
Jace
Celica2k

Jace
2000 Toyota Celica GT

Joined: Aug 2004
Posts: 993
Springfield, MO
Feb 3, 2:53pm - #390667 
need tips for puttin on dynamat

I'm ready to install so i was wondering what tips you all had for me. Do you all work with small pieces or go for the biggest piece possible? Do you put the dynamat over all the wires and everything else? Just let me know.

Joined: Aug 2004
Posts: 993
Celica2k
Jace
Celica2k

Jace
2000 Toyota Celica GT

Joined: Aug 2004
Posts: 993
Springfield, MO
Feb 3, 2:58pm - #390668 
how do you stop the vibration from the hatch handle? damn thing makes so much noise!

Joined: Jun 2004
Posts: 1,298
sickcelica696
Specialist
sickcelica696
2000 Liquid Silver Toyota Celica
Specialist
2000 Toyota Celica

Joined: Jun 2004
Posts: 1,298
Annapolis, MD
Feb 3, 3:08pm - #390669 
dont dynamat the wires...that would suck later. I used a rubber roller for the simple curves and a harder wooden roller for the intricate stuff. Peel it off then rool it on. When your done take a hair dryer or heat gun and lightly go over it again after you warm itmthis will make it stick better. As far as the handle goes i dont know..thats the only thing left that rattles on my car also..

Joined: Feb 2003
Posts: 347
vaio23
Member
vaio23
2003 Spectra Blue Toyota Celica
Member
2003 Toyota Celica

Joined: Feb 2003
Posts: 347
Baytown, TX
Feb 3, 3:11pm - #390670 
I dynamatted my doors a while back. I recommend using big pieces to cover up the large wholes in the doors then cut smaller pieces to fill the surrounding areas. It is just a matter of preference some like using large pieces and other small strips. Just make sure to test fit before you take the backing off then heat the piece with a hairdryer before you put it on, then go over it with a roller. As for the wires many people just dynamat over them but since I did it myself I took the time and cut all the holes for the wiring clips, that way the mat is more secure to the door panel. For the hatch you just have to take the plasic trim off from the inside and dynamat the entire hatch, I still have to do this. His is a few pics of my doors.

Linked Image

Linked Image

Join the conversation - Register Now or Log In to add your comment


Moderated by  isaac 

Member Spotlight
sincere2883
sincere2883
2000 Toyota Celica
New York

Posts: 244
Joined: November 2003
Thanks: Toyota
Show All Member Profiles 
Shout Box
Recent Topics
E-brake and seized brake caliper
by osirhc17. 04/27/2017 10:27 AM
TradingGTS for GT what should I know.
by GTS25430. 04/24/2017 5:19 PM
Does 01' corolla struts swap in an 01' celica GT?
by Frostysnowman92. 04/24/2017 1:22 PM
WTB: 00-02 amp bypass harness
by MJ00GTS. 04/18/2017 7:36 PM
Does not seem to be much activity for the 5th gens???
by Coop301. 04/18/2017 7:51 AM
Cold wet weather hesitation
by GTS25430. 04/17/2017 6:15 AM
00-02 premium 8spkr 2din gps solutions?
by MJ00GTS. 04/17/2017 2:24 AM
WTB: valve assy, vacuum switch
by hydraea. 04/15/2017 5:32 PM
Customize Your Toyota Celica Privacy Policy · About · Contact
Privacy Policy · About · Contact
CelicaHobby.com is an independent Toyota Celica enthusiast website. CelicaHobby.com is not sponsored by or affiliated with Toyota Motor Sales, USA, Inc. in any way. The Toyota and Celica names and logos are trademarks owned by Toyota Motor Sales, USA, Inc.
© CelicaHobby.com, 2001-2017
Powered by UBB.threads™ PHP Forum Software 7.6.1
(Snapshot build 20170416)