Previous Thread
Next Thread
New Reply
Print Thread
Rate Thread

Joined: Jul 2004
Posts: 236
Member
2001 Toyota Celica GT
Member
2001 Toyota Celica GT
Joined: Jul 2004
Posts: 236
Ok i just got the blue line series undercar neon kit by streetglow. anyone know how to install them. i looked thought all that instruction stuff but still confused. someone pls help me

Joined: Jan 2004
Posts: 114
Member
2000 Toyota Celica GT
Member
2000 Toyota Celica GT
Joined: Jan 2004
Posts: 114
all you have to do is hook them all to a fused line to the battery. I dont know how to really explain it but pretty much it goes battery-fuse-switch-bulbs. If this doesnt help just wait for someone smarter to answer. wave

Joined: Nov 2002
Posts: 1,073
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Nov 2002
Posts: 1,073
^^^thats it. You have a transformer (the little black box with 4 sets of +/- slots). This gets wired to the battery, and to a switch. I mounted my switch in the dummy slots on the dash. Mount the lights under the car, run the wires to the transformer, hiding them and tucking them and mounting them so they have no play. This is important. Put all the wires inside looms for two reasons...One if you get moisture in the wiring or bulbs, they will burn out. Two..it will get the wires from rubbing and shorting out. The transformer I mounted down behind the drivers side headlight. Its not hard to set up all the wiring, etc. but the more time you take insulating, looming, hiding mounting etc. the longer your system will last. I learned the hard way, I have had three complete sets on mine. Moisture is definately the enemy. Oh, some systems come with a way that the lights run from one light to the other in a series and not all four into the transformer. Same basic concept though. I hope this helps. Just take your time. thumbsup

Joined: Jun 2004
Posts: 1,298
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Jun 2004
Posts: 1,298
blue line doesnt have the 4 slots,atleast mine didn't. Its a daisy chain of the tubes making a loop with the transformer in it. ground the system to the battery if you want the brightest illumination, or a strong engine point. Use a good gauge insulated wire like a 8 or around there and put a 15amp inline fuse off the battery. Run that through a 15amp switch and back to the transformer and everything should work

Joined: Aug 2004
Posts: 539
Senior Member
2000 Toyota Celica GT
Senior Member
2000 Toyota Celica GT
Joined: Aug 2004
Posts: 539

Joined: Jul 2004
Posts: 236
Member
2001 Toyota Celica GT
Member
2001 Toyota Celica GT
Joined: Jul 2004
Posts: 236
how do you put all the wires inside looms(whats this word mean) so theres no moisture

Joined: Nov 2002
Posts: 1,073
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Nov 2002
Posts: 1,073
looms are a plastic cover that goes over the wires. There are spiral kinds, and ones with just a slit. The wires go inside them to protect them.

Joined: Jul 2004
Posts: 236
Member
2001 Toyota Celica GT
Member
2001 Toyota Celica GT
Joined: Jul 2004
Posts: 236
i don't think they came with the package. do i need to loom all the wires or just some of them. also how do you get all the neon tube wires from under the car to under the hood. can you mount the distribution behind the foot pedal or something or wheres a good place? also what is wire clamps? do i need them?

Joined: Nov 2002
Posts: 1,073
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Nov 2002
Posts: 1,073
looms did not come with the kit. Buy them at auto zone. You don't have to have them, but it will make your lights last longer. I would loom them all. Your lights run in a series so they run from light to light and then run them up into the engine compartment, any way you want as long as they are hidden away and don't contact anything hot that would melt them, or any moving part. I put mine up inside the inner fender liner and through the hole in the underside top of the frnder into the engine compartment on the drivers side. It is a good idea to mount the transformer inside the car so it doesn't get exposed to the weather. Your kit should've come with clamps that fastenen the wires. All they do is mount the wires (anywhere) so they don't move around. I also used the universal solution...zip ties!! Once you get started on it, a lot of the stuff I'm telling you will make sense.

Joined: Jan 2004
Posts: 114
Member
2000 Toyota Celica GT
Member
2000 Toyota Celica GT
Joined: Jan 2004
Posts: 114
Make sure when you mount the wires you really clamp them good. I thought I did mine good but last winter my wires got pulled out. you know the snow that clumps up right behind the front wheel, well my wires got frozen into that chunk and then it fell off when I was going in reverse and I ran it over. It pulled the wires out of the tubes. angry

Joined: May 2004
Posts: 2,971
Boobie Vision
2000 Toyota Celica
Boobie Vision
2000 Toyota Celica
Joined: May 2004
Posts: 2,971
yeah I just installed my street glow yesterday, me and my dad did it, we just followed what the diagram said and it was cake dude. Just follow instructions and you will be ok. BTW my neons are red.

Joined: May 2004
Posts: 2,971
Boobie Vision
2000 Toyota Celica
Boobie Vision
2000 Toyota Celica
Joined: May 2004
Posts: 2,971
But what was the hardest and bitches part of it all was getting the wire for the switch through the firewall of the car! OOH MAN!! have such little space and your upside down lol. It was a bitch to do but it was fun.

Joined: Apr 2004
Posts: 802
Senior Member
2004 Toyota Celica GT
Senior Member
2004 Toyota Celica GT
Joined: Apr 2004
Posts: 802
I reinforced the moisture part by siliconing all the parts where the wires go into the tubes. After that I put split loom on the wires and siliconed inside of the looms. They're moisture bulletproof now. thumbsup Just an extra precaution. grin


Originally posted by RICOGT:
i wanted to get the vac gauge because it constantly moves. more of a race feel i think

Joined: Jul 2004
Posts: 236
Member
2001 Toyota Celica GT
Member
2001 Toyota Celica GT
Joined: Jul 2004
Posts: 236
how do i clamp the wires(pic will be great) how much are the wire loom to cover all the wires? where should i put the tubes for the sides? thanks for all the input guys. thumbsup

Join the conversation - Register Now or Log In to add your comment


Link Copied to Clipboard
Member Spotlight
nebraskaGTS
nebraskaGTS
2000 Toyota Celica
Nebraska

Posts: 451
Joined: December 2003
Random: John stop humping my car.
Show All Member Profiles 
Recent Topics
Spyder Headlight LEDs
by Dxnxld - Mar 25, 2024 6:51am
Anyone ever hear this noise?
by CeliacCelica - Mar 21, 2024 10:51am
Clunking sound (not sure where from)
by Juliansky - Mar 20, 2024 3:01am
Does anybody know where i can find a S53 trans rebuild kit?
by MoreRamenNoodles - Mar 19, 2024 8:57pm
Urgent
by SoloXKay - Mar 19, 2024 11:58am
OEM speedometer on aftermarket ecu
by Penaman99 - Mar 5, 2024 11:23am
Brake master cylinder
by Nigel100 - Mar 5, 2024 2:45am
newly purchased 2000 GTS
by CantShift - Feb 27, 2024 9:06pm
Customize Your Toyota Celica Privacy Policy · About · Contact
Privacy Policy · About · Contact
CelicaHobby.com is an independent Toyota Celica enthusiast website. CelicaHobby.com is not sponsored by or affiliated with Toyota Motor Sales, USA, Inc. in any way. The Toyota and Celica names and logos are trademarks owned by Toyota Motor Sales, USA, Inc.
© CelicaHobby.com, 2001-2024
Powered by UBB.threads™ PHP Forum Software 8.0.0
(Preview build 20230331)