Previous Thread
Next Thread
New Reply
Print Thread
Rate Thread
Page 1 of 2 1 2

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Celica GTS DC Sport Header Install Guide

I finally finish installing my header yesterday it took me 2 days so if you dont have mechanical experience just take it to a shop.

I'm not responsible if anything goes wrong do this at your own will

Tools you will need to finish this installation
- set of socket wrenches from 10 mm to 14mm
- set of wrenches from 10mm to 14mm
- an adjustable wrench (for the sensor on the exhaust)
- extension for socket wrench 20
- pipes, long pipes -- not too long, just fat enough to fit the wrench handle. this will be used for more leverage. it makes the installation much easier

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Step one
First you need to disconnect your negative battery terminal (10 mm)
(Note: you should just remove the whole battery, its going to have to come out later on)
1870145519-DSCN3220.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Step two
Under the car you need to remove your dirt guard, to make it easier to reach jack up the car but dont lift it off the ground, you dont need to do this till later, just enough to give you room to get under and take out all the bots and nuts and shit, ill point were they are in the picture below
1870145523-DSCN3221.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Picture two
on each side of the car were your wheel is located take out the 3 screws or what ever they are out of the way, ill point them out do this on both sides
1870145525-DSCN3222.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Step Three
First disconnect the 4 ignition coil harnesses pointed in the picture
1870145527-DSCN32232.JPG

Last edited by Clos; Aug 1, 2004 7:58pm.

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Then remove the 4 ignition coil bolts on top of the valve cover (10 mm)
1870145535-DSCN3223.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now remove the bolts and the 2 harnesses shown in the picture below
1870145537-DSCN3224.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Step Four
Its time to take out the valve cover but first we need to get this two nuts (10 mm)
1870145538-DSCN32233.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Next remove all 9 screws from the engine cover
1870145539-7.jpg

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
2
1870145540-8.jpg

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
3
1870145541-9.jpg

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now your engine should look like this
(note: credit for the last 3 pictures goes to the teamcelica installation guide on the lift bolts)
1870145542-DSCN3225.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
also make sure you cover the camshaft and everything around it. i used a clean paper bag and put it on top so no dirt and shit could get on it

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Step Five
Now there are 5 screws on the top heat shield ill post the right hand side of it and then the left side okay
1870145547-DSCN3226.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
left side
sorry the harness in on the way but you can find it if you got this far
also i removed the battery to get to this bolts, you should do the same
1870145549-DSCN3229.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
to make this easier use the pipes i told you to get put them at the end of the wrench and this should make it a lot easy to break the bolts and save you a lot of strength
(note from now on you should use this method to break every bolt)

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Its time to get under the car
Jack up the car and make sure you put it on jack stands you dont want to die trying to install something.
Now we are trying to get the bottom part of the heat shield off there should be only four on this one the first picture are the ones closes to the engine and the one ones are away from it
1870145554-headshelfunder.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
far side
1870145556-headshelfunder2.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Note I tried everything I could to get the heat shields out at this point but its kind of impossible so dont try it would be a waste of time
(credit for the last 2 pictures go to the person that made the other installation guide on the header)

Last edited by Clos; Aug 1, 2004 8:10pm.

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Step Six
Remove the bracket that holds the header there are 3 bolts there (14mm)
Make sure you hold it its heavy and might hurt you if it falls on u
1870145559-DSCN3230.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Step seven
Now we are going to take out the exhaust pipe to make this a whole lot easy
First take out the 2 bolts connected to the header there 14mm
1870145561-DSCN3231.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now go down the end of the pipe and get the other two there also 14mm
1870145563-DSCN3232.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now disconnect the sensor by using an adjustable wrench
1870145568-DSCN3239.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
second sensor
1870145569-DSCN3238.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
And try to do this to get the rubber hooks out of the exhaust
1870145571-DSCN3234.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now its time to make more room
Remove the heat shield it has 4 nuts there 10 mm
1870145573-DSCN3235.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now remove the other head shield there are 2 nuts 10mm right under the hood here is a pix now there should be about 2 more nuts under the car get them off before you can remove that heat shield I forgot to take a picture of it sorry but if you got this far you can figure it out
1870145575-DSCN3236.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now with all of this out you should be able to try to get the head shield out im not saying its going to be easy because even with this it was hard what I did was take the top head shield out of the top of the car and when it was not coming out I started to harmer it and it came out and the bottom one just pull it and move around to get it out

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now here is the biggest bitch to do, getting the header screws out
There are 5 here is the picture
(Note the only screws you can get from above the car is the one in the middle I took all the other ones from under the car
(picture credit to the other install guide)
1870145583-stock header.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
Now on the other installation guide they say to remove some shit that has to deal with the suspension but I dont think he remove his pipe thats y he had to do this.
Now pull the header just the way it is it should come out it took me 15 mins to figure it out. Basically just pull it from under the car grab it by the ass and just pull it dont turn it or anything you should have enough room to get it out.
After you get it off put the new one on just the way you took the stock one out, it should not be hard after that bam youre done.
Here is the after pix from under the car and above it
1870145592-DSCN3237.JPG

Last edited by Clos; Aug 1, 2004 8:23pm.

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
note i had not bolt the exhaust to the header yet so yeah. the fitness is perfect and i can feel a lot of torque and a lot more power wen im in the 7 rpm range, great mod thumbsup
here is the pix from above
1870145603-DSCN3240.JPG

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
any questions feel free to ask
and yes i did left the heat shield off. why? i dont know you dont have to leave it off but i just left it off because i was 2 lazy to put it back on, but if you want 2 you can put it back on, it should fit perfect

Anonymous
Unregistered
Anonymous
Unregistered
awesome bro...nice guide...glad to hear all went well...hope your hand heals tongue

and congrats thumbsup

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
yeah its gettin better hahahah to bad my friend got more hurt then i did thumbsup thanks danny you asshole lets go to the track to see wat we get (beat that asshole enrique and his gay altima)

Joined: Nov 2002
Posts: 342
Member
2000 Toyota Celica
Member
2000 Toyota Celica
Joined: Nov 2002
Posts: 342
Great install guide, thanks a lot! thumbsup

Now i'll be sure to install em when i get em...


Not just another girl's car...

Joined: Jan 2004
Posts: 311
Member
2000 Toyota Celica
Member
2000 Toyota Celica
Joined: Jan 2004
Posts: 311
nice guide, i like the yellow hands! thumbsup


"I didnt realize girls had that much plumbing down there. I saw a diagram of it and it looked like a map for six flags."

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
and also make sure ya spray some WD40 on all the bolts. to make it easy

Joined: May 2003
Posts: 1,296
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: May 2003
Posts: 1,296
awsome guide man! thumbsup

Joined: Jul 2004
Posts: 31
Member
2004 Acura RSX
Member
2004 Acura RSX
Joined: Jul 2004
Posts: 31
That damn header was a bitch time ten to put in. Oh well, it was worth it. thumbsup

Joined: Oct 2003
Posts: 1,154
Specialist
2003 Toyota Celica
Specialist
2003 Toyota Celica
Joined: Oct 2003
Posts: 1,154
thumbsup thumbsup thumbsup This will help a lot when I get my header.

Joined: Feb 2004
Posts: 47
Member
2000 Toyota Celica
Member
2000 Toyota Celica
Joined: Feb 2004
Posts: 47
Great guide! I didn't even think to pull out the battery to get to some of the bolts when I put mine in. They were a little bit of a pain but after it's done you feel great. thumbsup

Joined: Jul 2003
Posts: 493
Senior Member
2000 Toyota Celica
Senior Member
2000 Toyota Celica
Joined: Jul 2003
Posts: 493
did you reuse your gasket or buy another one b4 hand??

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
nah
i just use the same one it was not that worn out so you should be good thumbsup

Joined: Aug 2003
Posts: 874
Senior Member
2000 Toyota Celica
Senior Member
2000 Toyota Celica
Joined: Aug 2003
Posts: 874
What is the factory tourque for tightening the bolts? And I do not mean "as hard as you can", or "The tighter the better". There has to be a spec. Thanks.

Last edited by cooltoy2000; Aug 28, 2004 5:28pm.

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
it dosent say any were that you have to torque them, and i would say as hard as you can, you want the right torque call dc or ur local toyota dealer, it has to be tight enough so you wont get licks and get that ugly sound

Joined: Sep 2004
Posts: 895
Senior Member
2004 Toyota Celica
Senior Member
2004 Toyota Celica
Joined: Sep 2004
Posts: 895
WHAT YEAR IS UR CELI???

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
2000

Joined: Feb 2004
Posts: 1
New Member
2002 Toyota Celica GTS T-Sport
New Member
2002 Toyota Celica GTS T-Sport
Joined: Feb 2004
Posts: 1
help me
i have a european model, i have EGR valve.
help me!!!

Joined: Oct 2003
Posts: 3,037
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Oct 2003
Posts: 3,037
wat year is ur car, i dont know bro i cant help you there, but im seeling my header i need money right now so i dont know

Joined: Aug 2003
Posts: 371
Member
2003 Toyota Celica
Member
2003 Toyota Celica
Joined: Aug 2003
Posts: 371
Originally Posted by totyfru
help me
i have a european model, i have EGR valve.
help me!!!

You can't use the DC header with an EGR valve, it says it right on the box, before you even open it.

1870225506-screen.jpg


[Linked Image]
Page 1 of 2 1 2
Join the conversation - Register Now or Log In to add your comment


Link Copied to Clipboard
Member Spotlight
BLACKGHOST
BLACKGHOST
2003 Toyota Celica GT
IL

Posts: 35
Joined: January 2004
Thank you.: Mama thomas, michelle, mike, scooby,leeo,heavensknight crew westbury,ny
Random: Night time is my time come out and play see ya in the streets.
Show All Member Profiles 
Recent Topics
Spyder Headlight LEDs
by Dxnxld - Mar 25, 2024 6:51am
Anyone ever hear this noise?
by CeliacCelica - Mar 21, 2024 10:51am
Clunking sound (not sure where from)
by Juliansky - Mar 20, 2024 3:01am
Does anybody know where i can find a S53 trans rebuild kit?
by MoreRamenNoodles - Mar 19, 2024 8:57pm
Urgent
by SoloXKay - Mar 19, 2024 11:58am
OEM speedometer on aftermarket ecu
by Penaman99 - Mar 5, 2024 11:23am
Brake master cylinder
by Nigel100 - Mar 5, 2024 2:45am
newly purchased 2000 GTS
by CantShift - Feb 27, 2024 9:06pm
Customize Your Toyota Celica Privacy Policy · About · Contact
Privacy Policy · About · Contact
CelicaHobby.com is an independent Toyota Celica enthusiast website. CelicaHobby.com is not sponsored by or affiliated with Toyota Motor Sales, USA, Inc. in any way. The Toyota and Celica names and logos are trademarks owned by Toyota Motor Sales, USA, Inc.
© CelicaHobby.com, 2001-2024
Powered by UBB.threads™ PHP Forum Software 8.0.0
(Preview build 20230331)