Previous Thread
Next Thread
New Reply
Print Thread
Rate Thread

Joined: Feb 2003
Posts: 916
Senior Member
2003 Toyota Celica GT
Senior Member
2003 Toyota Celica GT
Joined: Feb 2003
Posts: 916
Here's a writeup of my headlights paint job. I'll include tips and things I learned along the way. I did them in gunmetal, using Duplicolor wheel & rim paint. The color was "graphite" I chose wheel & rim since it was the only one at that store that came in graphite. Looking at the can, it says for wheels and PLASTIC hubcaps, so I knew I was in business. First off, wear gloves, they get hot, being in the oven & all. And wear some old junky clothes because you'll probably get some epoxy on you.

Here's a pic of the can of paint I used. It might be different in the USA, but I picked it up at Canadian Tire for like 7 bucks.

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

So here I am in the garage, first order of business is taking the bumper off, and then removing the lights.

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Tip#1: undo the silver screw on the side by the fender last, it supports the light while you take out the top & bottom screw.

Everyone knows about the 3 brass screws, but there's also 2 little rubber nozzles with sponge filters I was NOT expecting to see. Take these off too since they probably wouldn't fare too well in the oven. In the top pic, one is shown along with the DRL which I also removed. Second pics show's them removed. (obviously)

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

And the top one, along with the lowbeam rubber seal which should be removed along with the bulb, as in the next pic (yeah the bulb's still there but I did take it out)...

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]


Take out the 3 screws on the lowbeam seal and it comes right out. I'm not sure what the hell those other 2 things are but they didn't seem to be going anywhere so I left them. Survived the oven fine so no big whoop.

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Next comes the oven.

Tip#2: place the towel on the rack and "pre fit" the light in the oven with it off. Then you have an idea how far into the oven it has to go.

Turn on the oven to 300F. When it hits that temp, open it up, stick in the towel, and place the light on the towel so it doesn't melt on the rack. Have the rack on the lowest one. I used "bake" instead of "broil". Turn it off, close the door and start the timer. I left it the full 15 minutes before I took it out.

Tip#3: don't be afraid to get some help. I had my kid help me take them apart, his job was to unclip the clips on the side of the light with a butter knife while I pulled. ALSO, VERY IMPORTANT... Start at the top, when you get the top opened a bit, stick the knife in between and jimmy it open. The rest should go as smooth as can be. The sides of my light didn't get wrinkled at all like you sometimes see. I just kept pulling and pulling. Only had to do it once, didn't have to reheat the oven. But leave it in the full 15 minutes. Use an old butter knife as it gets some gunk on it. Here's one of the lights apart...

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Tip#4: to take the insides out, remove the 2 screws, the jimmy it apart. Start at the top, be careful since you don't want to break the damn thing. When you put them back together you'll notice it just sort of drops in from the top and snaps into place, so do it reverse to take it out. The side opposite the screws has a little tab. Note it's path, it needs to be pulled up. It will take a little fiddling but it comes out. Then bend up the tabs carefully on the reflector and take it out. The single tab will lift up first, and then you can pull it out. Don't get carried away bending it up and down since it will get weaker each time you do and eventually break.

Next up...decide if you are going to paint the top or the underside. I wanted the ribbed look, so I decided to paint the underside. This being said, it's wise to totally mask everyting on the top, since as you spray it goes pretty much everywhere. Take your time, do a good job, we're only going to do this once... right? Don't worry, if you fcuk it up, you can always paint the top. grin

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Flip it upside down, paint it someplace dry and not dusty, if you're doing it in a garage, pull any vehicles out since paint might get on it. Stands to reason right? But you never know. When it's upside down, you can see if you missed any spots.

Tip#5: On the first one, I tried to follow every curve perfectly with the masking tape. On the second one I let it overlap, with the overlap hanging in the air. I made sure that it was on tight by running my fingers over top and pressing it down really tight. By spraying light coats, it sholdn't wick paint under the crack. It didn't for me, but again, I pressed it down really well.

Next, paint the mofo. Use light strokes, again, take your time and do a good job. You don't want it running all over. I did 2 coats. Took a while on each coat to get it all, and then waited oh, about 1/2 an hour between coats. Then let it dry a couple of hours or so.

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Wait until it's dry and then peel the tape off. Take care as some paint on the tape might be wet. You don't want to get it on your hands or on the light. Once it's off admire it. Damn that's a thing of beauty.

Tip#6. If there's little bits of glue from the masking tape, or epoxy on the outside, use duct tape to remove it. Yup, duct tape, is there anything it can't do?? Take a little piece and stick it over the leftover adhesive. Then peel it back. You'll see it pick up a bit. It will take some time but it will totally remove it. It's better then wiping it off with windex, or rubbing alcohol, or what-have-you, since it takes it off clean instead of spreading it around.

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Put it back together now. Before you do, take a bit of windex and clean it up. ALso make sure the painted part is totally clean and everything is clean. I got the second light together and was giving it a once over before I stuck it back in the oven and wouldn't you know it. There was a damn HAIR on the inside of the light. REALLY look at it at this point, since you REALLY don't want to pull it apart again.

Insert the reflector and bend the tabs back down. Do the double tab side first then set it down on the single tab. Next, slide the painted part into the clear light cover. If the light were on your car, slide the painted part down, and you'll see how that tab clicks right into place. Then press the other sides down and put the screws in.

Next, place the 2 halves together, be careful and line them up properly. Even though it is cold, the epoxy still sticks together pretty good. I heated the oven back up to 300, and this time put them in for 8 minutes since I didn't want to melt the paint or anything. (I don't know if that would happen but I didn't want to take the chance) When it comes out press it together and the pieces should slide in nicely. Put the 3 brass screws in at this point and it will really suck the whole thing together. Here's some pics of them done...

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

And both lights together, completed.

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Replace all the little rubber filters, the DRL's and the rubber seals for the lights.

Tip#7: put your lowbeams in before you install the lights back on the car. WAY easier.

Slap them back on the car...

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Put the bumper back on and voilla. Easy mod, I'd do it again in a heartbeat. Set aside a day to do it, since the painting takes the time. But don't be afraid. I was hesitant at first but it was a piece of cake. Having a helping hand when you take it apart might be all the difference in the world.

A couple more pics of the final product. Oooooooooooh... Aaaaahhhhhhh. Rock and roll. Hope this helps out with some of the details and tips & tricks

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

[Linked Image from i1187.photobucket.com] [s1187.photobucket.com]

Rob

Last edited by CaffeineKid; May 31, 2019 10:51pm.

Joined: Oct 2003
Posts: 254
Member
2000 Toyota Celica GT
Member
2000 Toyota Celica GT
Joined: Oct 2003
Posts: 254
great guide smile thanks man , still afraild to mess it up

Joined: Feb 2004
Posts: 1,716
Specialist
2000 Toyota Celica
Specialist
2000 Toyota Celica
Joined: Feb 2004
Posts: 1,716
That's a nice job you did. The light luk awesome. Is that an Injen intake i see you had hook up??

Good job

Joined: Jan 2004
Posts: 5,125
Speed Omen
2002 Toyota Celica GT
Speed Omen
2002 Toyota Celica GT
Joined: Jan 2004
Posts: 5,125
very nice... good job with the guide thumbsup

Joined: Jan 2004
Posts: 305
Member
2000 Toyota Celica
Member
2000 Toyota Celica
Joined: Jan 2004
Posts: 305
first off rob they look sick. they look awsome painted against the yellow. and thanx for putting out all of the steps out with pics of exactly wat you did. because i am planning on doin this too and had no idea where to start. thanx a lot grin


[Linked Image from roundtwo0.tripod.com]

Joined: Jun 2003
Posts: 1,305
Specialist
2002 Toyota Celica GT
Specialist
2002 Toyota Celica GT
Joined: Jun 2003
Posts: 1,305
Nice! thumbsup

Joined: Oct 2003
Posts: 945
Senior Member
2000 Toyota Celica
Senior Member
2000 Toyota Celica
Joined: Oct 2003
Posts: 945
Looks good!

Joined: Aug 2003
Posts: 6,365
Likes: 1
Caleb
2000 Toyota Celica
Caleb
2000 Toyota Celica
Joined: Aug 2003
Posts: 6,365
Likes: 1
Originally Posted by round2gts
first off rob they look sick. they look awsome painted against the yellow. and thanx for putting out all of the steps out with pics of exactly wat you did. because i am planning on doin this too and had no idea where to start. thanx a lot grin

ditto.

now THAT is awesome and a very nice job with the pics & install. great job, i can't say enough.

although we already have a similar guide on here about painting your headlights, it definately wouldn't hurt to give isaac a pm and ask him about taking a look at your guide to see if he can put this up as well.

again, great job. thumbsup

Joined: Feb 2003
Posts: 916
Senior Member
2003 Toyota Celica GT
Senior Member
2003 Toyota Celica GT
Joined: Feb 2003
Posts: 916
Quote
ditto.

now THAT is awesome and a very nice job with the pics & install. great job, i can't say enough.

although we already have a similar guide on here about painting your headlights, it definately wouldn't hurt to give isaac a pm and ask him about taking a look at your guide to see if he can put this up as well.

again, great job. thumbsup

Sure man, he can put it up with the other guides. The more information, the easier it gets for the next person. Whoever was the first person crazy enough to even think about it had some balls man! grin

Rob

Joined: Jul 2002
Posts: 10,110
05 WRB
2005 Subaru WRX STi
05 WRB
2005 Subaru WRX STi
Joined: Jul 2002
Posts: 10,110
that's so fuckin awesome eek grin


SUBARU TECNICA INTERNATIONAL

Joined: May 2003
Posts: 1,296
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: May 2003
Posts: 1,296
thats sweet! maybe a ill set aside a day during spring break to try that... lol

Joined: Sep 2003
Posts: 416
Senior Member
2000 Toyota Celica
Senior Member
2000 Toyota Celica
Joined: Sep 2003
Posts: 416
holy thats sooo niceee thumbsup thumbsup thumbsup

Joined: Apr 2003
Posts: 4,650
Rebel
2003 Toyota Celica GT
Rebel
2003 Toyota Celica GT
Joined: Apr 2003
Posts: 4,650
Originally Posted by Sultan
very nice... good job with the guide thumbsup


[Linked Image]

Joined: Oct 2003
Posts: 1,061
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Oct 2003
Posts: 1,061
VERY nice! Good work! I've been thinking about doing that, but i'm afraid to mess up the headlight housings...

Oh what the hell... i've already started painting my interior, might as well do the headlights too rofl

By the way, for people who have any other questions about painting, you can refer to my paint guide, which should answer your questions. Paint away!

robare99, Keep up the good work!


[Linked Image]

Joined: Feb 2004
Posts: 269
Member
2000 Toyota Celica GT
Member
2000 Toyota Celica GT
Joined: Feb 2004
Posts: 269
Great job, and thanks for the guide!

Joined: Feb 2003
Posts: 916
Senior Member
2003 Toyota Celica GT
Senior Member
2003 Toyota Celica GT
Joined: Feb 2003
Posts: 916
Yeah man, go for it. Remember, God hates a coward. LOL it's easier than it sounds, but I think the key is an extra set of hands when you take them apart. Then a little time & patience.

Rob

Joined: Jul 2003
Posts: 1,274
Specialist
2001 Toyota Celica GT
Specialist
2001 Toyota Celica GT
Joined: Jul 2003
Posts: 1,274
BAT should make n overlay for this maybe is he could... confused


DJ CURTIZ - taking over the world one record at a time
Live life on the edge, otherwise you take up too much space.

Joined: Aug 2003
Posts: 2,925
Specialist
02 Toyota Celica
Specialist
02 Toyota Celica
Joined: Aug 2003
Posts: 2,925
thats sickk dude...good job thumbsup


[Linked Image]

Joined: Oct 2002
Posts: 608
Senior Member
Senior Member
Joined: Oct 2002
Posts: 608
Yaah. Nice work. Still scared to take mine apart. I really do not want to f... it up wtf

Joined: Apr 2003
Posts: 894
Senior Member
Senior Member
Joined: Apr 2003
Posts: 894
sweet dude! they look like the 03 headlights now thumbsup


rip celi...
95 240sx

Anonymous
Unregistered
Anonymous
Unregistered
excellent man i hope i can do mine as well as yours...great job! thumbsup thumbsup thumbsup thumbsup thumbsup

Anonymous
Unregistered
Anonymous
Unregistered
here is a contrast...
1869866056-405708_61_full.jpg

Anonymous
Unregistered
Anonymous
Unregistered
and the other...
1869866059-405708_76_full.jpg

Anonymous
Unregistered
Anonymous
Unregistered
oooo, thats nice, much easier to compare!

Joined: Jan 2004
Posts: 2,371
SHO - NUFF
2003 Toyota Celica GT
SHO - NUFF
2003 Toyota Celica GT
Joined: Jan 2004
Posts: 2,371
just wow!!! that's super clean, but not something I think I'd have the brass to do...headlights in the oven scares me...incredible job tho.

Joined: Dec 2003
Posts: 411
Senior Member
2003 Toyota Celica
Senior Member
2003 Toyota Celica
Joined: Dec 2003
Posts: 411
That's crazy man thumbsup
hope you don't mind if i copy u... rice
...just looks to dam good to pass up grin

Joined: Jan 2004
Posts: 8
New Member
2000 Toyota Celica GT
New Member
2000 Toyota Celica GT
Joined: Jan 2004
Posts: 8
Anyone planning on doing this make sure you have lots of time, i read this yesterday 7th of march and decided to do it, i was out there from 430 pm to 1230 am, lolo... but the end result was way worth it no doubt. i also installed my trd front bumper and fogs, and my trd plate from bullet racing (thanx that shiz is tite)... so that took some time... but his directions are dead on balls accurate, ill post some pix soon, i just want to say thanx for posting that install guide you gave me a lot of direction in something i had no idea in doing... my gf also helped me the whole way, she was a big help except when she was complaining, as women do..lolo jk or not..

to those who try this good luck, just remember in the end it will be worth it!

Joined: Feb 2003
Posts: 916
Senior Member
2003 Toyota Celica GT
Senior Member
2003 Toyota Celica GT
Joined: Feb 2003
Posts: 916
Robare99 here. OP has been updated (2019)!
Just updating the post with new pic links.



Last edited by CaffeineKid; May 31, 2019 10:48pm.
Join the conversation - Register Now or Log In to add your comment


Link Copied to Clipboard
Member Spotlight
toysport_celica
toysport_celica
2000 Toyota Celica
Ca

Posts: 52
Joined: August 2004
Thank you.: me, myself, and I...!
Random: a bowl of rice, fried chicken, and a glass of water!
Show All Member Profiles 
Recent Topics
Spyder Headlight LEDs
by Dxnxld - Mar 25, 2024 6:51am
Anyone ever hear this noise?
by CeliacCelica - Mar 21, 2024 10:51am
Clunking sound (not sure where from)
by Juliansky - Mar 20, 2024 3:01am
Does anybody know where i can find a S53 trans rebuild kit?
by MoreRamenNoodles - Mar 19, 2024 8:57pm
Urgent
by SoloXKay - Mar 19, 2024 11:58am
OEM speedometer on aftermarket ecu
by Penaman99 - Mar 5, 2024 11:23am
Brake master cylinder
by Nigel100 - Mar 5, 2024 2:45am
newly purchased 2000 GTS
by CantShift - Feb 27, 2024 9:06pm
Customize Your Toyota Celica Privacy Policy · About · Contact
Privacy Policy · About · Contact
CelicaHobby.com is an independent Toyota Celica enthusiast website. CelicaHobby.com is not sponsored by or affiliated with Toyota Motor Sales, USA, Inc. in any way. The Toyota and Celica names and logos are trademarks owned by Toyota Motor Sales, USA, Inc.
© CelicaHobby.com, 2001-2024
Powered by UBB.threads™ PHP Forum Software 8.0.0
(Preview build 20230331)